Backpack Cleaning Machine-manufacture,factory,supplier from China

Laser cutting machine maintenance and cleaning skillsLaser cutting is the laser beam irradiated to the workpiece surface through the release of energy to melt and evaporate the workpiece, in order to achieve the purpose of cutting and engraving process. With high precision, fast cutting, and not limited to the cutting pattern limit, automatic typesetting save materials, smooth incision, low processing costs, will gradually improve or replace the traditional cutting process equipment.

Laser cutting machine maintenance and cleaning skillsLaser cutting is the laser beam irradiated to the workpiece surface through the release of energy to melt and evaporate the workpiece, in order to achieve the purpose of cutting and engraving process. With high precision, fast cutting, and not limited to the cutting pattern limit, automatic typesetting save materials, smooth incision, low processing costs, will gradually improve or replace the traditional cutting process equipment.

Laser engraving machine maintenance guide1, laser engraving machine in the process of use should be strictly in accordance with the correct startup order to open or close the equipment (note: laser power must be preheated for 5 minutes!) .2, in the process of laser engraving machine, must be at any time to detect the water temperature (the best working water temperature is 25~30℃, the highest water temperature can not exceed 35℃, the lowest water temperature can not be less than 5℃), once the water temperature is high, should immediately change the water.

Laser engraving machine use precautions1. When using automatic focal length, it is necessary to pay attention to whether the automatic focal rod is fastened. If the automatic focal rod is loose, it will cause the top of the workbench to the laser.2. When laser engraving machine is working, it is forbidden to open the boot cover.3. Open the smoke exhaust and smoke blowing equipment during processing.4, processing wood, paper, must pay attention to the processing speed to avoid fire.5.

Laser engraving machine in the process of the use of skillsBefore starting work, you should carefully check the spelling of the text portion of the engraving project, and if conditions permit, print the contents and confirm with the customer. If you want to avoid the dislocation of the sculpture in the process of engraving, you need to do a good job of prevention, and implement the corresponding solution when the dislocation problem occurs.Error checking:a. Check whether the pliers or clamp used for engraving are wrongb. Whether the pliers or clips are wornc.

Laser cutting machine equipment common faults and solutions1, boot without any response▶ Power fuse is burnt out: Replace the fuse.▶ Power input is normal: Check power input and make it normal.▶ Main power switch is damaged: Replace the main power switch.2, no laser output or very weak laser▶ Optical path offset: Carefully adjust the optical path.▶ Contaminated or damaged reflector lens: Clean or replace reflector lens.▶ Whether the focal length of the device is changed: readjust the focal length.▶ Focusing mirror is contaminated: Clean the focusing mirror.▶ Cooling water quality or temperatur

　　The galvanometer calibration of the laser marking machine is one of the key steps to ensure the accurate and efficient operation of the marking machine. The galvanometer is one of the core components of the laser marking machine, and its angle and position accuracy directly affect the quality and accuracy of marking.

How to install laser engraving machineThe installation of laser engraving machine has the following three steps:1. Installation(1) Insert the control card into the microcomputer PCI slot, tighten the screws, and connect the data cable; Plug in the USB dongle and install the operating software and dongle driver.(2) Connect the laser tube water circulation tube with the anode and cathode conductor, and then put the laser tube clamp ring.

The reason why the laser head of laser engraving machine does not glowIn the daily use of laser engraving machine, it is often encountered that the laser head of the laser engraving machine does not glow. This article briefly introduces how to deal with the laser head of the laser engraving machine.1.

　　Portable laser marking machine is a device that uses laser technology to marking, which is usually used to engrave text, patterns, logo on the surface of various objects. It has the feature of simple operation, flexible operation, good engraving effect, and is widely used in jewelry processing, crafts, mold processing, woodworking, leather processing, paper-cut engraving and other fields. So what is the conventional voltage of the portable laser etching machine?